Misc. parts needed for full widh swap
4 posters
Page 1 of 1
Misc. parts needed for full widh swap
dana 60 pinion flange to toy driveline
10 bolt pinion flange to toy driveline
spool or locker for 30 spline dana 60 full float
locker for 10 bolt (front)
5.38 gears for both
drag link for 10 bolt
10 bolt steering arms
brake lines from toyota to dana 60 (ford) and 10 bolt (gm) respectively
10 bolt pinion flange to toy driveline
spool or locker for 30 spline dana 60 full float
locker for 10 bolt (front)
5.38 gears for both
drag link for 10 bolt
10 bolt steering arms
brake lines from toyota to dana 60 (ford) and 10 bolt (gm) respectively
Blackdog- BIG TIME MONKEY
-
Number of posts : 548
Age : 39
Location : Reno
Job/hobbies : Fireman
Rig : '91 toy Xcab on 1 tons, dual cases
Registration date : 2007-12-20
Re: Misc. parts needed for full widh swap
let me guess
the spool i gave you is 35 spline
and i still have the high steer rear steer arms for ya
the spool i gave you is 35 spline
and i still have the high steer rear steer arms for ya
Guest- Guest
Re: Misc. parts needed for full widh swap
tubebuggy wrote:let me guess
the spool i gave you is 35 spline
and i still have the high steer rear steer arms for ya
:yesnod: you are correct good sir!
Oh yeah, forgot you had those :smack:
Blackdog- BIG TIME MONKEY
-
Number of posts : 548
Age : 39
Location : Reno
Job/hobbies : Fireman
Rig : '91 toy Xcab on 1 tons, dual cases
Registration date : 2007-12-20
Re: Misc. parts needed for full widh swap
ja i have the tie rod off of my 60 sitting at my house that you can have it it will work for you, poly performance also now carries the pinion flanges and there is a set of 5.38 gears on ebay right now at around 80 buck. Jeepcampingworld on pirate quoted me around 450 for 5.38's and set up for 2 axles
carlos(4dees) has a company in his build thread that can make you brake lines for like 45 for 27" long banjo fitting to toyota metric. If not foothill offroad has them also
carlos(4dees) has a company in his build thread that can make you brake lines for like 45 for 27" long banjo fitting to toyota metric. If not foothill offroad has them also
snowshoebrue- Gearhead Monkey
-
Number of posts : 344
Age : 44
Location : modesto
Job/hobbies : electrician
Rig : 2003 tacoma truggy
Registration date : 2007-12-20
Re: Misc. parts needed for full widh swap
hey chris g. isn't there a parts mike or something like that?
BIG BLING- KING KONG
-
Number of posts : 1962
Age : 48
Location : S SAC
Job/hobbies : AUTO RESEARCH TECH/ wheelin and building junk
Registration date : 2007-12-19
Re: Misc. parts needed for full widh swap
yeah, I checked out parts mike, some of his stuff is good, some is over priced. I found a website that sells USA standard gears for $155 and the install kit for $77 for each axle.
I've got the tie rod off my 10 bolt, I'm just not sure if its up to the strength of an aftermarket drag link.
I'll have to check out ebay, thanks justin.
How'd you go about your steering justin? or did you go hydro?
I've got the tie rod off my 10 bolt, I'm just not sure if its up to the strength of an aftermarket drag link.
I'll have to check out ebay, thanks justin.
How'd you go about your steering justin? or did you go hydro?
Blackdog- BIG TIME MONKEY
-
Number of posts : 548
Age : 39
Location : Reno
Job/hobbies : Fireman
Rig : '91 toy Xcab on 1 tons, dual cases
Registration date : 2007-12-20
Re: Misc. parts needed for full widh swap
Well, if you run the Hi-steer rob has, you need heims or drill it for 1 ton tre (tie rod end).. If you go any other hi-steer, I believe it is all 1 ton tre drilled or straight drilled for heims also.. I don't believe a stock 10 bolt tre is the same size as 1 tom stuff. I can almost be sure it isn't. If you just want to run the low steer, stock center link) double check the holes for the tre's are both top or bottom drilled. I believe they are opposite each other.. if they are, just keep extra tre's on hand.. Oh yeah, I may be interested in that spool also..
cdgvw1- BIG TIME MONKEY
-
Number of posts : 598
Age : 48
Location : Rancho Cordova, Ca.
Job/hobbies : Editor, wheelin, Air Cooled VW's, RC truck's, buildin shtuff....
Rig : 77 K5, 1 tons, 4.56:1, locked rear, 400/465/203/205 (triple sticked & want it on 42's)
Registration date : 2008-01-18
Re: Misc. parts needed for full widh swap
Blackdog wrote:
How'd you go about your steering justin? or did you go hydro?
i used wfo steering on my truck. i have my tierod behind the axle but i don't know if it is gonna work. it looks like the tie rod is gonna hit the oilpan. and my axle is too far forward for standard highsteer so i might go full hydro or put the tierod in the stock position
snowshoebrue- Gearhead Monkey
-
Number of posts : 344
Age : 44
Location : modesto
Job/hobbies : electrician
Rig : 2003 tacoma truggy
Registration date : 2007-12-20
Re: Misc. parts needed for full widh swap
cool guys, thanks.
Blackdog- BIG TIME MONKEY
-
Number of posts : 548
Age : 39
Location : Reno
Job/hobbies : Fireman
Rig : '91 toy Xcab on 1 tons, dual cases
Registration date : 2007-12-20
Re: Misc. parts needed for full widh swap
so it looks like I need a 4.56 and up carrier for the D60 now.
Justin, how much do you want for that tie rod?
Justin, how much do you want for that tie rod?
Blackdog- BIG TIME MONKEY
-
Number of posts : 548
Age : 39
Location : Reno
Job/hobbies : Fireman
Rig : '91 toy Xcab on 1 tons, dual cases
Registration date : 2007-12-20
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
|
|